Essential Plumbing Tips for Installing a Bathtub
Essential Plumbing Tips for Installing a Bathtub
Blog Article
This post listed below on the subject of Installing A Bathtub is without a doubt interesting. Check it out for yourself and see what you think about it.
Mounting a bathtub isn't specifically rocket science, but it does require strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a new one is also a reasonably hard job. If the old tub is conveniently easily accessible, the job can relocate immediately; if you need to open up a wall to get rid of the old tub as well as place the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also embeded in the brand-new one. See to it you have actually certified yourself for the work as well as fit attempting it. As opposed to employing a contractor to take over a halfway-completed project, it is better to take into consideration employing one before you start. Opportunities are you might need an expert plumber to make tube connections.
This article will certainly aid you install a new bath tub in your bathroom if you have already acquired a new tub as well as don't need to change the arrangement of your previous water pipelines.
Your devices and also product checklist need to consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted accessibility that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the staying water that will originate from the pipelines. As soon as the supply pipes have actually been eliminated, utilize the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming during this process. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Before moving on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washing machines remain in area in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. As soon as the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former type must be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Tub
Making use of the two wood boards under its feet, put the bathtub in the required setting. The wood boards are helpful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the tub up until the level checks out level.
To install taps, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the very same for the other faucet.
Switch on the water system and also examine all joints and brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as additionally inspect the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and sealing around the tub must wait up until the bathtub has actually been made use of at the very least when as this will certainly settle it right into its final position.
Preparing for the Setup
To start with, the supporting frame provided with the bathroom needs to be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps system to prevent pressure on the tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, resulting in problems with moisture and feasible leaks to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are offered in tubes as well as cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to always load the bathtub with water before securing, to enable the movement experienced when the tub is in usage. The sealant can crack fairly early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also easily offered on the market. It is advisable to fit the floor tiles using waterproof or water resistant sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about How to Install a Bathtub Yourself? Put feedback down below. We'd be pleased to find out your ideas about this write up. We hope to see you back again before long. Liked our content? Please share it. Let other people discover it. Thanks a lot for your time. Kindly come visit our blog back soon.
Rates Report this page